Sun and water

zoom

Muath Bani Hani looks at the benefits of a centralised domestic solar water heating systems in UAE applications.

A solar hot water system works by collecting solar radiation through solar panels fitted on a roof. The heat is then transferred to water storage for daytime use.

Solar collecting systems are usually classified as passive or active. Passive systems collect and distribute solar energy without the use of an auxiliary energy source, they are dependent upon building design and the thermal characteristic of the material used.

Active systems consist of components that are, to a large extent, independent of the building design and often require an auxiliary energy source (pumps) to circulate the water from the storage tank, through the collectors and back into storage.

The circulating pumps are turned on automatically by an electronic differential thermostat. This device reads the different temperature in the collectors and the storage tank. Pumps are turned on when the water temperature in the solar collectors is higher than the storage tank water.

It is recommended that a timer is used to automatically turn off the recirculation pumps between the hours of 12:00 am and 5:30 am, or that a variable speed pump is used for further pumping power optimisation.

When demand for hot water use is minimal the Aquastat only activates the recirculation or controls the VFD drive pumps when the water in the line falls below 150OF (65.6OC). Active systems are more easily applied to existing buildings.

Generally solar heating systems for domestic hot water include: a solar heating collector panel to collect the solar radiation that will be converted and stored as thermal energy; a fluid system (water) to transport the stored energy from the collector panel to its point of use; and a hot water storage tank to store the heated water by the solar collectors' panels for day and night use.

Collectors may also be classified as fat-plate or vacuum tube. High-performance flat-plate or vacuum tubes are generally required for cooling applications, since higher temperatures are needed to drive absorption-type cooling units.

Evacuated tubes are composed of two glass tubes made from tough borosilicate glass. The outer tube is transparent allowing the suns rays to pass through with minimum reflection.

The inner tube is covered with a special coating, which gives excellent solar radiation absorption and minimized reflection properties. The tops of both tubes are fused together and air in the space between the two layers of glass
is evacuated.

This "evacuation" of the air forms a vacuum, and is an excellent insulator. The insulation properties are very efficient that while the inside of the tube is so hot, the outer tube is cold to touch. The main problem with this type of collector is that the efficiency decreases significantly when they get covered by dirt and dust, so frequent cleaning is needed.

The flat-plate consists of an absorber plate, cover glass, insulation, and housing. The absorber plate is usually made of copper and coated to increase the absorption of solar radiation. The cover glass (or glasses) is used to reduce the convection and radiation losses from the absorber. The housing holds the absorber (insulated on the back and edges) and cover plates.

The working fluid (water, ethylene, glycol, air, etc.) is circulated in a serpentine fashion through the absorber plate to carry the solar energy to its point of use.

Print | Email | Discuss this article

| Share |

READERS' COMMENTS

whats so great about this article
Posted by Markus on Monday 5 October 2009 at 11:20 UAE time


I don’t get the point of this article, this is elementary physics, something you can Google or wiki..Where is the business element in the piece?
Basically how can you apply this to real life and with a sound business case.......

Great Job
Posted by Khaldoon, Doha, Qatar on Sunday 4 October 2009 at 20:31 UAE time


Very interesting article, it reflects the deep knowledge of the author. well presented and organized, direct to the point, focus and rich.

good Job Eng. Muath, wishing you success and prosperities.

The everlasting energy source
Posted by Youssef Nasser on Tuesday 13 January 2009 at 11:41 UAE time


I never knew that the system could "over-heat", and thus making it a challenge to have in the gulf region.
All buildings should definately consider using solar power as the best way to heat water as this article suggests. However, it shouldn't just stop at "Sun & Water", which might solve the "over-heat" issue by utilising the extras to other means.
Afterall, the Sun is the life bearing planet!

excellent article
Posted by Mohamed Ibrahim, sharjah, U.A.E on Tuesday 13 January 2009 at 10:26 UAE time


Very rich and will presented article which show a good knowledge in the subject, well done Engineer Muath Bni Hani

Click here to post a comment

Add your Comment All posts are sent to the administrator for review and are published only after approval. ArabianBusiness.com reserves the right to remove any comment at any time for any reason. Please keep your responses appropriate and on topic. Arabian Business would like to point out that only comments relevant to the story will be published. Any containing personal insults or inappropriate language will not be approved.
Name *
Remember me on this computer
Email *	(Your email address will not be published)
City
Country
Subject *
Comment *
Notify me of further comments
Enter the words above *
Please click post only once - your comment will not be published immediately.

MORE FROM ARABIANBUSINESS.COM